It's been a while since I have purchased any 1:20.3 Bachmann steam engines and I would like to know what you guys think a used or new C-19 # 346 should be worth and same question for me K-27 # 456. Thanks in advance for any help.

Would someone be able to tell me the original cost of the C-19 # 345 or #346. black in colour with the flying Rio Grande on the tender. Also what would be a reasonable price to pay for one today if one could be found. Thanks in advance.

Does anyone know where I can get drawing of the C-19 road pilot with dimensions to build one like the Bachmann C-19 one.                                                                                       How about you Mr Bachmann, any suggestions please.

Does anyone have a road pilot for the K-27, looking to replace a damaged one.

Thanks for your help, I will now look to purchase some JIS screw drivers and see how they work to remove those screws

Is there anyone out there that can get me the dimensions of the road pilot by Bachmann.
Thanks in advance if you can help.

Does anyone need tender switcher steps for a K-27 ( used in excellent condition )
Engine switcher pilot ( used in excellent condition )
I also have a BACHMANN - Dog House in unopened wrapper
All are for sale or trade for K-27 / C-19 Road Pilots

Does anyone in the 1:20.3 community have a spare road pilot for the K-27, made
by Bachmann and the the Bachmann road pilot for the C-19.
I am willing to pay for each if available.
I think I just purchased the only remaining, K-27 road pilot on the internet and need 1 more.
Thanks in advance if you can help.

I am attempting to remove screws on my K-27, witch hold on the tender road switcher long steps,
under the rear coupler, witch are no long required and on the C-19, again removing the
tender switcher steps, witch are again, under the coupler, and no longer required.
My problem is removal of the tiny, little screws that hold them on, and replace with proper road steps.
I have tried using phillips #0 and the smaller #0-2 with almost not luck upon extraction of the screws
holding the steps on. Usually 2 screws per side.
Short of using a vice grip on the head of the crew, and twisting them out. witch to date is my only option,
so far, does anyone have any suggestions or instruction of how you have removed these little buggers,
and without ruining the heads of them so they can be reused to put on steps.

To the Bachmann,
Now that the D&RGW's T-12 #169 is back in service,
Is Bachmann Industries, considering, manufacturing the T-12 engine in the 1:20.3 scale.
I know all about tooling, costs etc, blah, blah, blah.
I would like an honest answer of ,
Yes we will be manufacturing it, and when.
Very seriously considering it, and that's all.
Have no intension of manufacturing it, even in the now or in the near future.
I myself and many of the 1:20.3 scale friends would like a honest answer.
Thanks in advance for your answer, relieving may of us of the unanswered question.
We your devoted customers can handle the truth.
Again Thanks Mudhen,

Read your information and find it to be right on as per running my K-27's and C-19 on my outdoor railway.
With my grades I can usually run with 2 to 5 cars including caboose max.
You made me fell better about my engines tractive pulling power. They in my opinion on my layout are
running prototypically. I originally thought the engines where way under powered.

I have always had the best of luck with the installation of Revolution Decoders and Phoenix
sound in my Bachmann K-27's and C-19
I just watched a video of the QSI Titan sound system  ( Bachmann C-19 with QSI Titan ) Check it out.
on Youtube , and I was quite impressed.
The QSI Titan was changed to a QZ-FX
Has anyone tried to install a QSI Titan in one of these Bachmann engines.Preferably the C-19
If you have what was involved in the installation of it.
What did you use for a controller and decoder system, For the QSI Titan.
My questions up front are,
Can a Revolution system and decoder be used, or do I need another control system, ( eg. Air-Wire ).
Can I use my 18.4 volt 6000 mll amp.
Does the speaker need to be changed.What about the Battery charging system and volume control.

Thanks in advance Mudhen

I would dare to say that the Bachmann !:20,3, D&RGW locomotives are very much prototypical on tonnage pulling.
.

I Have a stable of 1- C-19, 2-K-27s, and 1-K-28.
Can anyone tell me how many cars each should pull and on what type of grades.
The C-19 AND K-27S are battery powered..
I find the number very low unless double heading a train.
I am gouging to have to get to ball bearings in the side frames soon I think.
Thanks in advance

Thanks for your suggestions, Ordered today.