I have a number of locos stored that I would like to put into a particular sequence. Can this be done? How?
Thanks.

Need the track plug size.
Thanks

Will this unit handle multiple hand-held control units or do I need to upgrade?

Also, how many locos will it reasonably handle?

I assume a power booster will allow MORE locos to be controlled.

I have an analog Thomas engine that has a built-in 'chug' sound. Can this easily be switched off?

Purchased a DC Ringling Brothers F7A back when I first started. Now that I've gone full DCC I purchased a DCC Santa Fe F7A and switched the bodies. The original Ringling Brothers had silver side frame trucks while the Santa Fe had black side frames. Can they be switched and if so, what will it take?
Thanks in advance.

Hi Everyone,

Is 'DCC Sound Value On Board' as shown in the Bachmann Train Catalog the same as 'DCC W/Sound'. Question came up on an item For Sale on eBay (a new Bachmann F7A). Seller says that it contains Sound Value which is SoundTraxx Diesel sound package with Proto 567 prime mover, 3 air horns and bell in 16 bit sound.

Thanks

Just purchased the Gandy Dancer as a Christmas present for my grandson. I did a test run before wrapping and it seems to have a problem. In one direction it runs smoothly but when changing direction it runs in a jerky motion and is a bit noisy. Could the gears need a need a little lube? Any help will be appreciated.

Any suggestions on where I can find the EZ Track Switch Controllers? This is the one that the green 3-wire plugs into. I don't believe the have an individual part/item number.

What is the radius of the curved section of a #4, #5and #6 turnout? I know that on a 44561/44562 it is the same as an 18".

What is the difference between the two?

Can this power pack be repaired or should I just replace? The 'To Track' female connector looses contact with the male plug due to usage.

Can someone tell me what the wire gauge is that is used on the EZ Track remote switches?

Thanks

I have a fairly large HO layout using EZ Track. I'd like to setup all turnouts to be remotely activated. I looked at using the Bachmann Green Wire extensions to reach the turnouts but the cost is prohibitive ($10 for a 10' extension). I have 30+ turnouts. I'd like to make my own extensions. Does anyone know of wire connectors that will work with the very small wire gauge used by Bachmann? I've tried the standard connectors sold by Lowes/Home Depot/hardware stores/etc that are rated for 22 ga wire but the crimp doesn't always hold tight.

looking for suggestions on best way to add dcc/sound to Ringling Bros Circus diesel.

I've built a large HO layout (12 x 16 U-shaped) using EZ Track. I didn't want to use the Power Terminal track due to cost so I've had to solder all the power/siding leads. Right now I've got 20 individual blocks plus 1 reversing  loop. Soldering track connections is not my expertise. Some are pretty good/ok others are not ok, a few plastic ties melted, etc. It would be great if Bachmann had a low cost track power connection similar to other brands, Atlas comes to mind, that would allow the wire to be screwed to the track. I tried using the pre-soldered track connectors but the wire was so thin it would break very easily. Just a suggestion.

Thanks

Looking for suggestions for a different on-off-on momentary switch, preferably micro size, to replace the switch control that comes with the Bachmann EZ Track turnouts. I'm looking for about 25.
Thanks

Is the radius measured to the inside rail, middle of the rails or outside rail?

Just purchased a set of piers to be used with HO EZ-Track. Each pier was placed where 2 sections of track come together. Problem is  engines will not climb the 'ramp' with any rolling stock attached. Some wont climb at all. EZ-Track straights are 9" long. You wind up with a grade of a little over 5.5%. The rise is 3.5" and the run is 62.75. What would be the 'max' grade I should try for?
Thanks

Planning on moving from DC to DCC. I understand that DCC Ready means loco has the NMRA 8-pin plug installed and a decoder must be purchased. Looking at the Bachmann catalog, I see that some locos are DCC Equipped and others are DCC Sound Value-Equipped. I assume that all will run on straight DC power. What is the difference between the two.
Thanks

Need ideas on elevated track support. I'm looking at placing regular 8x16 concrete block on individual beds of tamped crushed stone at 4 foot intervals and spanning the blocks with treated 2x8's then securing the track to the wood. This would be a quick way of getting a fairly simple layout up and running. Good or bad idea? Better suggestions requested.

Thanks