Len. Thank you.

Will N scale Bachmann remote turnouts (ie 44862) accept a stationary decoder like Digitrax DS51K1 to actuate the motor?

Hunt
Thank you. I assume then that Kadee gauge will work with Bachmann rolling stock.

Where can I buy one?

The "CLOSED" or "THROWN" shown in my throttle display does not match the physical position of the turnout.
Anyway way possible to reprogram the turnout to make it match?

I push the programming button in the turnout to enter "programming mode" but nothing happens.
I know the turnout receives power because when I power the track the turnout's points rails swing back and forth once.
Ideas?
...
***CLOSED***
My turnout was defective.

 I have contacted the Parts department and they emphatically responded they do not sell replacement decoders for turnouts.

UNBELIEVEABLE! I was operating under the assumption that Bachmann was serious about model railroading. Not carrying replacement parts for their products --especially electronic components!, it is not professional.

I see many people read my problem. I also gather nobody ever encountered this problem/need. I guess I will have to spend $85 to buy a WHOLE NEW turnout. I will think twice in the future before I invest in Bachmann.

Posted by: rich1998   Posted on: Today at 12:38:01 PM
A suggestion would be to call the Parts department. The phone number is on the site in Parts, Service and Information. They are usually helpful.
.....

Will do. Thanks.

I suspect the decoder in one turnout (Bachmann HO 44131 NS EZ Track Command Right Hand Turnout (DCC On Board) is fried.

Is it possible to purchase a replacement?
...
***CLOSED***
Bachmann Parts stated they do not carry replacement for the decoder.

rich1998

View Profile Personal Message (Offline)   
   
Re: HELP Needed to program Bachmann DCC turnout with a DCS210+ AND DT602 throttle

Try this Group. I use to belong to it some years ago because I used Digtrax decoders.

...

I am active in both groups. So far no echo. I gather that DT602 and DCS210+ are brand new products without too much experience in the field.

AT the moment I'm following LEN advice. Let's see what happens.

Terry

I´m hoping too. I am running out of options. Digitrax and Bachmann are of not help. I have spend thousands for this layout thinking that using Digitrax and Bachmann was a good decision with respect of support. Both brands have good brand recognition. I´m very dissapointed with both. I am even considering scrap the whole project and sell the parts in eBay.

Thank you for your time.

Terry

I found and tried the article Digitrax KB341. However, the article mentions DT40x or DT500 series throttles, and the OPT or CV/WR buttons to save the info. The DT602 does not have such buttons.

The thing is I cannot find any instructions from Digitrax to program a turnout using specifically the DT602 throttle (newest model).

I just bought three locos from Bachmann with DCC on-board.
https://shop.bachmanntrains.com/index.php?main_page=index&cPath=258&zenid=uof0g4pp3ss7uonj2v0dem1ad1

I cannot find info using a Digitrax DT602 throttle to program a Bachmann DCC turnout. So far, Digitrax is not help.
....
***CLOSED***
With the help of many of you, THANKS!, and after finding my turnout was defective, I was able to resolve the problem.

rich1998
I find it is very easy to forget to include all pertinent information.
But I have another question for you.
I have an HO Bachmann GP7 loco with DCC "Sound Value" by SoundTraxx (not Tsunami or others) on-board.
I want to reset the mobile decoder to factory defaults.
You suggested CV8=8.
Looking at the loco CV's list, CV8 is "Manufacturing ID" and its value is 141 (SoundTraxx).
Is your suggestions still valid?