jbrock27:
I've been busy, just got back to this thread. Thank you for your reference.
All:
Wow, getting into the mechanics, math, axle spacing, unpowered center axles on some engines, etc. of the 1to1 engines was very eye-opening, educational, and a little confusing. But I can understand all the experimentation by the railroads - every little improvement helps the bottom line (and often employee safety).
However, thank you all for sharing the info (and jward I liked your first paragraph). And believe it or not I've had some real-world experience with this when, for 16 years, I made my living as an independent contractor bidding on and moving high/wide/overweight items in the US, Canada and Mexico (moved about 155 loads in that time period). What I'm getting at here is what you all have addressed - total weight per axle (railcar + load + tiedown materials), axle spacing, track condition, bridge restrictions, etc. However, in this work traction for movement was assumed and not directly addressed.
Donaldon:
You said, "I think maybe this isn't so. While it's true that a loco with six-wheel trucks has 50% more contact with the rails than does a loco with four-wheel trucks, the weight on each axle is only two-thirds as much as what the four-axle trucks have. That's going to make a significant difference in the larger loco's adhesion and will just about negate all of the difference afforded by having more metal on metal."
You're probably right - I've not weighted a 4-axle diesel engine to equal the same amount I do to my SD40-2s (total of 22 to 22.5 oz each). The reason is - generally not enough room, or I'm too lazy to stuff small cut-off pieces of lead weights into cracks and crevices. However, (and I know you all know this) on a straight weight-added-on basis (to a 4-axle and 6-axle engine) to their "nominal" capacity, our 6-axle engines (all 6 driving) almost always out-pull the 4-axle ones.
Or - do you have some 4-axle diesel engines that out pull your six axle ones? You might have - I'll bet some of those powered B units (filled with metal weight from the factory) can out pull some run-of-the-mill 6-axle units. Interesting - sort of like the real world.
So, what I'm learning is to be careful of what I say about railroad wheel-traction physics (and probably some other technical items.)
The railroads have spent over a century doing this in the real world, and you folks are sharing some of that learning.
Thank you again.
K487 (aka Doug)
I've been busy, just got back to this thread. Thank you for your reference.
All:
Wow, getting into the mechanics, math, axle spacing, unpowered center axles on some engines, etc. of the 1to1 engines was very eye-opening, educational, and a little confusing. But I can understand all the experimentation by the railroads - every little improvement helps the bottom line (and often employee safety).
However, thank you all for sharing the info (and jward I liked your first paragraph). And believe it or not I've had some real-world experience with this when, for 16 years, I made my living as an independent contractor bidding on and moving high/wide/overweight items in the US, Canada and Mexico (moved about 155 loads in that time period). What I'm getting at here is what you all have addressed - total weight per axle (railcar + load + tiedown materials), axle spacing, track condition, bridge restrictions, etc. However, in this work traction for movement was assumed and not directly addressed.
Donaldon:
You said, "I think maybe this isn't so. While it's true that a loco with six-wheel trucks has 50% more contact with the rails than does a loco with four-wheel trucks, the weight on each axle is only two-thirds as much as what the four-axle trucks have. That's going to make a significant difference in the larger loco's adhesion and will just about negate all of the difference afforded by having more metal on metal."
You're probably right - I've not weighted a 4-axle diesel engine to equal the same amount I do to my SD40-2s (total of 22 to 22.5 oz each). The reason is - generally not enough room, or I'm too lazy to stuff small cut-off pieces of lead weights into cracks and crevices. However, (and I know you all know this) on a straight weight-added-on basis (to a 4-axle and 6-axle engine) to their "nominal" capacity, our 6-axle engines (all 6 driving) almost always out-pull the 4-axle ones.
Or - do you have some 4-axle diesel engines that out pull your six axle ones? You might have - I'll bet some of those powered B units (filled with metal weight from the factory) can out pull some run-of-the-mill 6-axle units. Interesting - sort of like the real world.
So, what I'm learning is to be careful of what I say about railroad wheel-traction physics (and probably some other technical items.)
![Smiley :)](https://www.bachmanntrains.com/home-usa/board/Smileys/default/smiley.gif)
Thank you again.
K487 (aka Doug)