Need Help Please....

[rdrivast]

Hello,

Can anyone tell me which pieces are needed to build a loop with EZ track.....

Help...

[jward]

most likely, 12 pieces of 18" radius curve, or 16 pieces of 22" radius curve. you can insert pieces of 9" straight along each side as you see fit. one of the pieces should be a terminal track.

[Hunt]

jward , has told you what to use to make a circle and how to convert the circle into an oval.


Is your question how to make a reverse loop like is on each end of the following?



Or do you have something else in mind?

Will you use DC or DCC to run locomotives?

[rdrivast]

thanks pal .. exactly what I want to do. But I wonder what exactly is that parts need ez track. Since I have tried several times and do not add me parts. I tried with 18 "and 22.5" curved tracks, starting with a left turn 18 ".

[Jerrys HO]

rdrivast,

To make a loop depends on the turnouts and radius you are using. If you download the free trial of anyrail you can design it yourself for free up to 50 pieces. There is a large selection of track available.
https://www.anyrail.com/index_en.html

Jerry

[Hunt]

Build with HO Bachmann E-Z Track sectional track as follows.

The geometry is not precise requiring one slight forced connection

Fits in 4 x 6 space

For the loop on left
1 - 44565. Remote Left turnout #5
Start connecting track on through route
1 - 44592 Straight 2" (from Connector Assortment)
4 - 44511 Straight 9"
8 - 44501 Curve radius 18
2 - 44511 Straight 9"
2 - 44503 Curve radius 22"

[rdrivast]

Thank Hunt ... whether to force a little connection .. but it turned out ... thank you very much.
Now the proper electrical connection to operate the machines ..

[jward]

keep in mind that the loop section must be gapped and isolated from the rest of the layout. I suggest that you google reverse loop wiring and read up on how to wire this configuration before you try to build it. if you don't insulate both rails you will have a dead short

[Joe Satnik]

Dear All,

There are many solutions to make that turn-around loop,

you just have to play with your CAD program and a calculator (slope formula) till you stumble onto a No-Kink one.   

One No-Kink solution inspired by (totally ripped off from) Hunt:

For the loop on left

1 - 44565. Remote Left turnout #5

Start connecting track on through (mainline) route, precise order is important:

1 - 44513 Straight 2-1/4"

4 - 44511 Straight 9"

1 - 44501 Curve radius 18"-30 degrees to left

1 - 44509 (2/3) Curve radius 33.25"-12 degrees to left

1 - 44531 (Half) Curve radius 18"-15 degrees to left

6 - 44501 Curve radius 18"-30 degrees to left

2 - 44511 Straight 9"

2 - 44592-5  Straight 2" from straight fitter assortment, or 44541S,  Straight 2" from 90 degree crossing

2 - 44503 Curve radius 22"-22.5 degrees to right

For fun, build it on AnyRail.

Thanks to Bachmann for the large variety of E-Z Track pieces.

Free the 2" Straights. (Blast from the past.)

Hope this helps.

Sincerely,

Joe Satnik

[Joe Satnik]

Dear All,

Another No-Kink turn-around loop solution, a bit more elegant,

with pseudo-easments on the ends of the 18" curves, but not on the 22"R.

1 ea. 44565. Remote Left turnout #5

Start connecting track on through (mainline) route, precise order is important:

1 ea. 44592-3 Straight 1-1/4" from straight fitter assortment

1 ea. 44513 Straight 2-1/4"

4 ea. 44511 Straight 9"

1 ea. 44508 (1/3) Curve radius 33.25"-6 degrees to left (pseudo-easement)

1 ea. 44531 (Half) Curve radius 18"-15 degrees to left

7 ea. 44501 Curve radius 18"-30 degrees to left

1 ea. 44508 (1/3) Curve radius 33.25"-6 degrees to left (pseudo-easement)

2 ea. 44511 Straight 9"

2 ea. 44503 Curve radius 22"-22.5 degrees to right

1 ea. 44592-4  Straight 1.5" from straight fitter assortment

Again, try it on AnyRail.

Hope this helps.

Sincerely,

Joe Satnik

Edit:  replaced "-"(dash)  with "ea." for clarity

[Hunt]

Joe or anyone,
If you have time (or curiosity) calculate the cost of my slightly not geometrically precise but it works solution vs your precise solutions.

[Joe Satnik]

List prices or street prices?

[Joe Satnik]

One loop or two?

Entire cost of packages, including unused/leftover track pieces, or just what is used ?

Bulk/individual cost (where applicable) or just package cost?

[rdrivast]

Hey Joe ... your first proposal is more feasible .. The second proposal seems to be forcing much the union of the parts.

Without doubt, this post is achieving what I set out initially ... generate ideas for Ez Track .. perhaps many people like me who are starting in the hobby this track format is more friendly for the first scale models.

Thanks for the feedback and continue contributing ideas for the layout creation ...

[Joe Satnik]

RD,

Hmm, I think my second attempt fits fairly nicely on my AnyRail screen.

Perhaps I transcribed it wrong, or the order got messed up or something. 

I'll double check on my end... gotta run for a bit, though.

Joe